活性焦法烧结烟气脱硫率影响因素统计解析

摘要：为明确影响活性焦烧结烟气脱硫的主要因素，通过模拟试验和生产数据统计分析探究脱硫塔自上至下脱硫率变化趋势和各运行参数对脱硫率的影响。模拟试验表明，循环使用后的活性焦孔隙结构更加发达，表面含氧官能团含量增加，进而其初期脱硫性能低于新鲜活性焦，后期优于新鲜活性焦。错流式脱硫塔自上至下脱硫率先后经历100%、快速降低、缓慢降低等过程。生产数据统计分析表明，脱硫率与SO2质量浓度、O2体积分数、H2O体积分数、NH3与NOx物质的量之比、解析温度呈正相关，与活性焦床温度、体积空速呈负相关。其中，SO2质量浓度、体积空速、活性焦床温度对脱硫率影响最大。运行参数之间存在多重共线性现象，烧结漏风率升高或空气补加量增加将引起诸多运行参数的变化，但总体上有利于脱硫率的提高。     

煤油气共生矿井底板油型气赋存特征及防治

为了提高煤油气共生矿井油型气灾害治理的科学性，以黄陵二矿为例，采用现场测试、钻探取芯、跟踪观测、地质分析等多种方法，研究了采掘工作面煤层底板油型气分布特征、涌出规律和运移机理，并初步探讨了底板油型气体灾害防治措施。结果表明:底板油型气涌出点多位于底板砂岩储层上倾尖灭端和砂岩透镜体附近，呈现不连续区带状分布特征，涌出的油型气主要来自富县组砂岩层，涌出的动力主要为地层流体压力差，底板油型气通过地层中存在大量的断裂和裂缝、微裂缝系统进入采掘空间，采掘扰动是底板油型气异常涌出的工程诱导因素。建议加强油型气综合探查技术、油型气灾害预测预报技术、油型气综合抽采技术和智能化矿井建设等方面的研究。     

混炼方式对螺旋纳米碳纤维增强天然橡胶复合材料力学性能的影响

采用干法和湿法两种混炼工艺制备了螺旋纳米碳纤维(HCNFs)/炭黑(CB)/天然橡胶(NR)复合材料,通过扫描电镜、拉伸试验机和应变扫描仪分别对所制备复合材料的界面形貌、力学性能和Payne效应进行了测试分析,考察了混炼方式对复合材料宏观力学性能及Payne效应的影响。结果表明,与纯CB填料相比,在干湿两种混炼方式下,添加适量的HCNFs(1～6份)能提高HCNFs/CB/NR复合材料的300%定伸应力、扯断伸长率、拉伸强度和硬度。与干法混炼相比,湿法混炼能明显增强HCNFs/CB/NR复合材料的Payne效应,并提升在HCNFs高添加量(2～6份)条件下的拉伸强度和扯断伸长率,这主要源于湿法混炼能够有效改善HCNFs在橡胶基质中的分散性。     

超精密气体静压系统节流器法向随机微振动研究

以无气腔平面节流器为研究对象,对节流器流固耦合法向随机微振动进行了理论仿真和实验研究。受限于节流器厚度与气膜厚度尺寸的差异和输入初始边界条件,建立了节流器的COMSOL仿真简化模型,对节流器-气膜微流场进行双向流固耦合数值模拟。仿真结果表明,节流器的法向随机微振动幅值关于节流器中心对称,且由中心向边缘逐渐增大;微振动幅值随气体入口流速的增大而增大。实验采用纳米级激光测振仪,依次测量供气压力为0.1,0.2,…,0.5 MPa时尺寸为75 mm×50 mm×14 mm的HEXAGON双环联结型节流器多个不同位置的法向振动,实验结果表明,法向随机微振动幅值分布特性与仿真结果一致,关于节流器中心对称,且由中心向边缘逐渐增大,验证了节流器法向微振动的"跷跷板"振动形式;在0.5 MPa供气压力下,边缘振动幅值超过1 nm。对实验数据进行功率谱密度分析,结果表明不同供气压力下法向随机微振动均在9.4 kHz和10.6 kHz处产生较大功率,可认为与节流器-气膜流固耦合系统的固有频率有关。研究结果有效地揭示了节流器法向随机微振动的特性,为气体静压系统避开随机共振区、优化气体静压系统的设计提供了理论指导。     

Highly efficient chemical mechanical polishing method for SiC substrates using enhanced slurry containing bubbles of ozone gas

In this study, a highly efficient method for chemical mechanical polishing (CMP) of silicon carbide (SiC) substrates using enhanced slurry was proposed and developed. The enhanced slurry contains bubbles of ozone gas generated by ozone gas generator in pure water mixed with a conventional commercially available slurry. Therefore, the enhanced slurry has an oxidizing effect on the Si-face of SiC substrates. To confirm the effectiveness of bubbles enclosing ozone gas, both nano-indentation test and X-ray photoelectron spectroscopy (XPS) analysis were conducted. As a result, the hardness decrease of the Si-face of the SiC substrate was confirmed through the nano-indentation test, and the generation of reaction products was confirmed on Si-face of SiC substrate in the XPS analysis. According to a series of experimental results of our proposed highly efficient CMP method for SiC substrates, the removal rate can be increased when the enhanced slurry was applied, comparing with that for the not only conventional commercially available slurry but also commercially available dedicated slurry.     

贾燕1,赵永涛2,张红松2

为确定ZrO2/莫来石热障涂层的单层最佳厚度,采用有限元技术研究单层厚度对ZrO2/莫来石热障涂层热冲击应力的影响。结果表明,莫来石层厚度为0.25mm时,涂层表面及ZrO2/莫来石界面处具有最大热应力,而其它莫来石层厚度时涂层内部热应力则受莫来石层厚度影响不明显。当ZrO2层厚度为0.3mm时,ZrO2/莫来石涂层中的热应力在整个横向距离范围内保持稳定,而其它情况下涂层中的热应力则与ZrO2层厚度成正比。涂层表面处的径向热应力大于ZrO2/莫来石界面处的对应值。     

Simulation of producer gas flameless combustion with fresh reactant diluted by hot flue gas

Flameless combustion is considered as a flexible and efficient combustion process for low heating value gas fuel. This paper presents numerical simulations of premixed flameless combustion using producer gas as a fuel. Different initial conditions of the premixed fresh reactant (air/fuel mixture) and dilution levels are taken into account for the investigation. The numerical simulations were investigated using a network of chemical reactor models with the detailed reaction mechanism of GRI‐Mech 3.0. A threshold dilution level for flameless combustion fuelled by producer gas was determined. The numerical results show that dilution of the fresh reactant with hot combustion products and initial fresh reactant temperature play important roles in flameless combustion formation and its auto‐ignition behaviour, rather than equivalence ratio of the fresh reactant. In the flameless combustion regime, temperature and chemical concentrations were reduced while chemical kinetics process was decelerated, resulting in delay of the auto‐ignition process.     

单一低渗透突出煤层水力冲孔工艺优化应用分析

为了有效提高单一低渗透突出煤层的瓦斯抽采效率，以高压水射流冲击理论为指导，针对平煤股份八矿己组突出煤层特征建立数值模型，模拟分析水力冲孔应力分布规律，通过现场实测分析冲孔有效影响范围，进一步优化设计冲孔参数、指导现场施工。现场应用表明，水力冲孔是一种行之有效的方法，对单一低渗透突出煤层实施水力冲孔卸压增透、提高瓦斯抽采效果具有重要意义。